C82 - Dual Port Multifunction Board
From $158.00
To $1,673.00
CNC4PC
The C82 supplies full access to the power of the Ethernet Smooth Stepper board.
OVERVIEW
The C82 supplies full access to the power of the Ethernet Smooth Stepper board.
FEATURES
-
Designed for ESS AND ETHER-MACH motion controller.
-
Built-in PWM-Based Speed Control and Two Built-in Electromechanical Relays with NO and NC positions for spindle control.
-
The system monitors:
-
E-Stop
-
Safety Charge Pump.
-
VFD Fault.
-
Driver Fault.
-
Discrete Inputs and Outputs can be using with +5vdc TTL logic or 10-30vdc Logic.
-
Electromechanical Relay with NO and NC positions for general purpose (Port_2 16 or 17, jumper-selectable).
-
Microcontroller based SCHP.
-
Optoisolated inputs.Can be powered with a voltage between +10 and +30VDC.
-
Status LEDs on all input and Output connections.
-
DIN Rail mountable.
-
Pluggable Screw-On Terminals.
-
It is compatible with family of C34 connector boards that allow quickly connecting to popular drives connecting not just the step and direction signals, but also the fault and enable signals.
| SKU | C82_B |
|---|---|
| Manufacturer | CNC4PC |
Documents and Download
Product Manual
-
User manual Size: (2.96 MB) - Intruccion and connections
-
Go to blog
Drawings and CAD Files
-
C82REV3.2_CAD Size: (2.19 MB)
Software, Installers and Configuration Files
- Pendant Installer for Mach4 and ESS. Size: (1.58 MB)
- Software Mach4 ESS Ver2.5 ( C82 - C25XP ) Size: (2.75 MB)
- Mach4 / ESS Plugin configuration for C25XP, C82, C62 Size: (502.9 KB)
Wiring Information
- Wiring Sample C82 Rev3 with VFD Huanyang Size: (388.59 KB)
- Wiring Sample C82 Rev3 with VFD IMT Size: (1.78 MB)
- Wiring Sample C82 Rev3 with VFD Minarik Size: (1.96 MB)
- Wiring Sample C82 Rev3 with VFD WJ200 Size: (390.6 KB)
- Wiring Sample C82 Rev3 with PlasmaSens Out Size: (438.75 KB)
- Wiring Sample C82 Rev3 with MPG Pendant Size: (2.06 MB)
- Wiring Sample C82 Rev3 with VFD Huanyang Error Disable Size: (396.76 KB)
- Pinout C82 Rev3 Size: (193.42 KB)
- Wiring for C82 Rev3 with G320 Driver Size: (846.59 KB)
- Wiring for C82 Rev3 with DG4S Size: (1.71 MB)
- Wiring for C82 Rev3 with KL5056 Size: (905.22 KB)
- Wiring Sample C82 Rev3 with CAP04 Size: (603.54 KB)
- Wiring Sample C82 Rev3 with CAP04 Ver.2 Size: (568.79 KB)
- Wiring for MicroStep KL5056 with C82 and Plasma Size: (999.11 KB)
- Wiring Sample C82 Rev3 + C78 with CAP04 Size: (601.08 KB)
- Wiring Sample MicroStep KL5056 with C82 Size: (812.3 KB)
- Wiring sample Touch Sensor with C82 Size: (2.36 MB)
- Wiring sample THC1 with C82 Size: (706.25 KB)
- Wiring Sample C82 + Touch Sensor and THC Size: (2.89 MB)
- Wiring sample C82rev3.2 with VFD LEESON Size: (1.69 MB)
- Wiring Sample C82 With Inductive Limit Switch NPN NC Size: (920.71 KB)
- Wiring Sample C82 With Inductive Limit Switch PNP NC Size: (1.24 MB)
- Wiring Sample C82 With Inductive Switch Size: (1.94 MB)
- Wiring sample C82 for Encoder input Size: (2.39 MB)
- Wiring Sample C82 Smooth Stepper for Lathe Size: (869.58 KB)
- Wiring C82 for Lathe Size: (4.02 MB)
- Wiring for C82 Rev4 with DYN4 Size: (3.41 MB)
Videos
- Instructions for Mach4 Plugin Installation Video
- Go To
- PlasmaSensOut C82 Mach3 V3
- Download
- Plasma THC (Torch Height Control) Setup Using the CAP04 with CNC4PC C82 and MACH3
- Go to video
- Mach4 and Ethernet Smooth Stepper MPG Setup
- Go to video
Instructions
- Step by Step C82 for Setting up a for Mach4
- Go to blog
- Step by Step C82 for Setting up a for Mach3
- Go to blog
Old Documents
- User Manual C82 Rev2 Size: (2.3 MB)
- Step by Step C82 Rev2 for Setting up a for Mach3 Size: (774.61 KB)
- Wiring for C82 Rev3 with DYN4 Size: (837.7 KB)
- Step by Step C82 Rev2 for Setting up a for Mach4 Size: (791.47 KB)
- User Manual Rev.3 Size: (848.35 KB)
- User manual Rev 3.2 Size: (962.38 KB)
Frequently Asked Questions and Answers
- What is a Safety Charge Pump (SCHP)?
It is a watchdog. It is a feature in which the control software will send a pulse stream through a pin, as if it was moving an axis. Then a microcontroller on the breakout board will see that pulse stream and will know that the signals coming from the c...
Read more - I cannot get the green LED to enable on the breakout board
3 conditions must be met to get the enable LED: The board must be properly powered. Check the documentation on the board, as a misunderstanding on how it is powered is very possible. The board must be connected to a PC/Motion Controller which is c...
Read more - US and International modes of operations for VFDs (Variable Frequency Drives) and Speed Controllers
VFDs and motors have two way of operation, in the US we use CW and CCW, in the rest of the world, or INT (International) it is used START/STOP and DIRECTION. These settings can usually be adjusted VFD settings. The chances are that if you purchased the V...
Read more - What would be the best hp laptop to use with this Bob running mach 4?
Mach4 will run very good on most PCs and Laptops but you really need to have an external motion controller. Like the Ethernet Smooth Stepper, UC300ETH, Ether-Mach or PoKeys. The performance of the processor itself has to do more with the types of operat...
Read more - What is the purpose of the relay when wired to gecko drivers as shown in photo?
The C82 and most of our cnc4pc breakout boards have 3 relays. Two of them are intended to for use controlling a VFD and the 3rd one is a general-purpose relay that can be tied to the enable line via the SCHP (Safety Charge Pump), so it can be used to dri...
Read more - When I configure the multifunction board with smoothstepper board are the cables to connect them then included?
Yes, the ribbon cables and studs are included.
Read more - Why use Ethernet Connection for my Motion Controller?
The Ethernet Connection has many advantages over USB. It is more reliable as Ethernet runs a client-server connection, while USB runs as a Windows Device. If there happens to be any glitch in the communication, you can lose the USB d...
Read more - Should I use the C76 with the UC300ETH or C82 with the Ethernet Smooth Stepper for my Plasma?
You can use the C76 or C82, it is a matter of preference. They both work with Mach4. I will try to summarize the basic considerations: The UC300ETH may provide additional flexibility as it can also support UCCNC in addition to Mach3/4. It also depends...
Read more - The Analog Output to the VFD is not stable
The issue is related to noise coming back from the analog input terminals on the VFD. They are supposed to be isolated, but sometimes noise finds a way. There are two ways of fixing that: - Use shielded cables for the analog and its ground and ground the...
Read more - How do the inputs work on this board?
The board has independent input banks that use a common for the input bank. Each input uses a bidirectional opto that can take signals from +5 to +24vdc. So if you apply GND to COM1, then the inputs for that bank, will activate with a voltage from +5vd ...
Read more - How does the Spindle Control work on the CNC4PC Multifunction Breakout Boards
The relays are not directly tied pins in the configuration, as it is the breakout board that is driving the relays based on the step(PWM) and dir received from the controller and the US/INT Mode selected to drive the spindle. Please check this: https://ww...
Read more
